Description
What does this mean?
OBD2 Code P0335 Kia definition:
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 Kia will set.
Symptoms
Possible sumptoms of OBD code P0335 Kia
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination
Causes
Possible causes of OBD code P0335 Kia
Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM
Possible Solutions
Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there’s no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn’t be performed if you’re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.
Related Codes
P0385 Kia P0335 Kia P0385 Kia P0016 Kia P0017 Kia P0018 Kia P0019 Kia P0335 Kia P0336 Kia P0337 Kia P0338 Kia P0339 Kia P0385 Kia P0386 Kia P0387 Kia P0388 Kia P0389 Kia
The OBD2 Code Information Be Applicable For Kia:
2013 Kia Sorento,2013 Kia Provo Concept,2013 Kia Niro Concept,2013 Kia K9,2013 Kia Cross GT Concept,2013 Kia Ceed SW,2013 Kia Ceed,2013 Kia Carens,2013 Kia CUB Concept,2012 Kia Soul,2012 Kia Rio,2012 Kia Ray,2012 Kia Picanto,2012 Kia K2,2012 Kia Grand VQ-R,2011 Kia Sportage,2011 Kia Sorento,2011 Kia Pro Ceed,2011 Kia Optima Hybrid,2011 Kia Optima,2011 Kia Naimo Concept,2011 Kia KV7 Concept,2011 Kia GT Concept,2011 Kia Cadenza,2010 Kia Venga,2010 Kia Soul,2010 Kia Sorento,2010 Kia POP Concept,2010 Kia Forte Koup,2010 Kia Forte,2010 Kia Ceed SW,2010 Kia Ceed,2009 Kia VG Concept,2009 Kia Soul,2009 Kia Optima,2009 Kia No3 Concept,2009 Kia Magentis,2009 Kia Borrego,2008 Kia eco ceed Concept,2008 Kia Pro-cee-d,2008 Kia Picanto,2008 Kia KOUP Concept,2007 Kia cee-d,2007 Kia Rondo,2007 Kia Kue Concept,2007 Kia Carens,2006 Kia Sportage,2006 Kia Spectra
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Kia makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.
